![]() "Ethernet" (net 1) for the Ethernet and a zone "Basilisknet" (net 2)įor the internal network connection of the ethertap interface. Tap0 -seed -phase 2 -net 2 -addr 2.47 -zone "Basilisknet" Here isĪn example /etc/atalk/nf for a LAN:Ä®th0 -seed -phase 2 -net 1 -addr 1.47 -zone "Ethernet" Install and configure netatalk if you want to use AppleTalk. The drawback is that youĬan only use network protocols that Linux can route, so you have to That your Linux box has access to (especially, if your Linux box hasĪ dial-up Internet connection and is configured for IP masquerading, ![]() This approach will let you access all networks Virtual network and set the default gateway to the IP address of theÄ®thertap interface. Under MacOS, select an IP address that is on the Information on how to set up /dev/tap* device nodes and activate theÄ®thertap interface. Next, see /usr/src/linux/Documentation/networking/ethertap.txt for comment out the line "dev->flags|=IFF_NOARP " in ethertap_probe() insert "#define CONFIG_ETHERTAP_MC 1" near the top (after the You also have to modify drivers/net/ethertap.c "Netlink device emulation", under "Network device support", activate Under "Networking options", enable "Kernel/User netlink socket" and It also requires that youĬonfigure your kernel to enable routing and ethertap support: In this case, the "ethernet card description" must be the name Putting Basilisk II on a virtual Ethernet via the "ethertap" device. Networks that your Linux box routes (e.g. MacOS will only beĪble to talk to other machines on the Ethernet, but not to other Under MacOS (TCP/IP, AppleTalk, IPX etc.) but there is no connectionÄ«etween Linux networking and MacOS networking. The sheep_net module will allow you to run all networking protocols To "/etc/nf", the kernel should be able to load the moduleĪutomatically when Basilisk II is started. If you copy the sheep_net.o module to a place where it can be foundÄ«y the kernel module loader ("/lib/modules//kernel/drivers/net"To compile and install the module yourself: The sheep_net module is included in the Basilisk II sourceÄistribution in the directory "src/Unix/Linux/NetDriver". The "ethernet card description" must be the name of a real Ethernet Direct access to an Ethernet card via the "sheep_net" kernel module. Then, when you click Start, BasiliskII should start up from the newly installed system.1. Did you then start the GUI again and did you remove the MacOS8 and installer parts images from the list? Did you then quit the installer and shut down BasiliskII (and if it is still running also the GUI) Did you proceed and let the installer do its work (you will probably see an animation of the installation process) and was the installation completed successfully? Did you choose in the running installer the MacOS753 disk (the one you named and erased above) as destination for the installation? ![]() Did you then start the installer application in again a new window that opened? Did you then double-click the icon of the "Sys7.5 V7.5.3 CD Inst" that appeared on the desktop? Did you double-click the System 7.5.3 01of19.smi in the window of that disk? Did you open the OS753InstallerParts disk? Did you then name and initialize (or again erase) the MacOS753 volume? Did you startup from the DiskTools_MacOS80.image? ![]() Of course the settings in the GUI will look the same, you already set them.Ä«ut, with all three disk images in place in the volumes list. I do not think SheepShaver is better for running that game. But since, I have 0 experience and knowledge on these things, I can not be sure. My understanding is that if I can do emulation with Basilisk or Sheepshaver that will create the right conditions to be able to run the Barrack game. Is there a difference between using Sheepshaver and Basilisk II? My end goal is to be able to run this 1990s game called Barrack once I am successful with the emulation. I can try to do the emulation with Sheepshaver, instead of Basilisk II. And once again everything worked until the end where I faced the same problem with the floppy disk in the middle of the screen with a question mark. The only thing is I used a different ROM this time (Performa). I checked that they are according to the instructions and they were. Of course, the settings were already configured in Basilik II. I tried to do the Basilisk II process again from the beginning.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |